Precise Forms Accessories - Alphabetical

Click the image for additional information.

  • Anchor Strap open Anchor Strap as shipped

    Anchor Strap

    The galvanized steel Anchor Strap is an alternative to the “J” Bolt style anchoring system. The product conforms with most code criteria. Check local building codes. The nail hole pattern allows for many plate sizes. Available in several sizes and types. Packaged 50 to a box.


  • Beam Block-Plastic

    Beam Block-Plastic

    Precise plastic products are light weight yet extremely durable. The Plastic Beamblock is easy to handle and will not fill with concrete like other beamblocks. The tapered design allows easy stripping.

    Precise Forms plastic Beam Blocks come in the following sizes.

    Description Width at form face Width at back of pocket Depth from top of wall down Depth from face of wall to back of pocket
    8" Wide Flange East Coast Beam Block Plastic 8 1/4" 7 3/4" 8 3/8" 4 1/2"
    10" Wide Flange East Coast Beam Block Plastic 8 1/4" 7 3/4" 10 3/8" 4 1/2"
    12" Wide Flange East Coast Beam Block Plastic 8 1/4" 7 3/4" 12 3/8" 4 1/2"
    8" Wide Flange Beam Block Plastic 6" 5 1/2" 8 3/8" 4 1/2"
    10" Wide Flange Beam Block Plastic 6" 5 1/2" 10 3/8" 4 1/2"
    12" Wide Flange Beam Block Plastic 6" 5 1/2" 12 3/8" 4 1/2"

  • Beam Block-Steel

    Beam Block-Steel

    The heavy duty Steel Beam Block is tapered for easy removal. Beam Blocks are C-clamped into place.

    Description A Dimension B Dimension C Dimension
    Standard 5" 4 1/2" Depth + 1/4"
    Wide Flange 6" 4 1/2" Depth + 1/4"
    East Coast 8 1/2"" 8" Depth + 1/2"

  • Bucko Vent.

    Bucko Vent

    The Precise forms Bucko Vent eliminates the need for a pouring buck as the frame of the vent is the same thickness as the wall. One size adjusts to fit 8" to 10" walls.


  • Cap Bracket.

    Cap Bracket

    Cap Brackets are used in conjunction with lumber to extend the wall height. The cap bracket has a 90 degree angle used as a seat for the lumber and a pin attached that is locked down through the pin hole in the end rail of the form. This provides for the ability to pull out some of the potential bowing that can be inherent in lumber.

  • Cap Bracket. Cap Bracket.

    The Cap Bracket can also be used to create wood fillers to allow pipes or other objects to pass through the wall without damaging your forms.


  • Concrete Chute.

    Concrete Chute

    The Concrete Chute helps you reach the hard to get at spots. It saves time of re-positioning the concrete truck and the labor of pulling concrete. It is made with extruded, not fabricated, aluminum for greater strength.

    The Extruded Aluminum Concrete Chute allows for those hard to get to pour points that the concrete mixer cannot reach. It is available in the following lengths: 8', 10', 12', 14', 16', 18', and 20'.


  • Concrete Porta Chute.

    Concrete Porta Chute

    The Porta Chute reduces splatter when placing concrete and minimizes the spilling of concrete in areas not to be poured. It is especially helpful during the pouring of footings. It connects easily to the end of the chute on the concrete truck.


  • To prevent the destructive and unappealing random cracking of expansive concrete, Precise Forms offers three unique sets of control joints. During the curing process, these relief joints provide control of the stress created as concrete contracts due to drying. Please specify hole pattern when ordering.

  • Control Joint.

    Control Joint

    Plastic control joints pin between forms prior to a pour. After stripping the hole tabs break off leaving a plastic control joint in the wall creating a clean Precise joint. These are a one time use joint.

  • Control Joint.

    The two piece 1 3/8” aluminum control joints pin between forms prior to a pour and are completely removed during the stripping process. The design creates a control joint that can be used for numerous pours.

  • Control Joint.

    Surface control joints are attached to the facesheet of the form to create a relief joint. They strip as the form is removed during the stripping process. Easy to relocate on the form, these aluminum joints are available in two sizes, 1/2” and 1”.


  • Form Puller.

    Form Puller Combo

    Form Pullers are used in tight situations such as corners and boxes. They are available in regular and combo.


  • Form Puller.

    Form Puller Left and Right

    Form Pullers are used in tight situations such as corners and boxes. They are available in regular and combo.


  • Form Puller for Dominator.

    Form Puller for Dominator

    Form Pullers are used in tight situations such as corners and boxes. This style is specifically designed to work with the Dominator Forming System.


  • Form Puller.

    Form Puller Long Handle

    Form Pullers are used in tight situations such as corners and boxes. The long handle provides more leverage.


  • Form Scraper.

    Form Scraper

    The cast aluminum form scraper provides an easy method of concrete removal on those spots where concrete has stuck to the forming system. Available in 6", 3" and 1 1/2" width. Also uses a replaceable carbide scraping blade.


  • Foundation Bolts (J-Bolts).

    Foundation Bolts (J-Bolts)

    Utilized in the securing of plates and other items to a cast in place concrete wall.

    Sizes available for 50 to a box packaged with nuts and washers.

    Length Type
    8" Standard
    8" Galvanized
    10" Standard
    12" Standard
    12" Galvanized
    16" Standard
    20" Standard

  • Hand Punch.

    Hand Punch

    This tool punches extra holes in forms for those special jobs or can be used to set bushings in side and end rails. It is much faster and more accurate than drilling.


  • Hurricane Strap.

    Hurricane Strap

    The galvanized steel Hurricane Strap is an alternative to the “J” Bolt style anchoring system. The product conforms with most code criteria. Check local building codes. The nail hole pattern allows for many plate sizes. Available in several sizes and types. Packaged 10 to a box.


  • Pin Pusher.

    Pin Pusher

    The use of attached hardware sometimes leads to the locking pin penetrating into an inside corner rather than projecting out of the Inside Corner. This tool allows for easy removal of pins with leverage pushing the pin out rather than attempting strike it with a hammer. The nose of the pin pusher is cupped to assist in remaining in position on the tip of the pin.


  • Plywood Adapter.

    Plywood Adapter

    Plywood Adapters can be used when running pipes or electrical through a wall. Holes can be cut into the plywood providing a pass through and preventing damage to the aluminum form. They also allow the easy creation of odd sized fillers.


  • Pouring Board (Flat).

    Pouring Board (Flat)

    The Precise Forms Pouring Board assists in the flow direction of the concrete into the forms. This allows for the concrete that is being delivered by the concrete mixer to be directed into the forms and thereby reducing potential concrete spillage.


  • Pouring Board (Flanged).

    Pouring Board (Flanged)

    The Precise Forms Pouring Board assists in the flow direction of the concrete into the forms. This allows for the concrete that is being delivered by the concrete mixer to be directed into the forms and thereby reducing potential concrete spillage. The flanged model allows for even more flow control.


  • Rod Supports.

    Rod Supports

    Rod Supports hold the re-bar in place in the footing during the pour. Available in single or double supports.


  • Saddle Bracket. Saddle Bracket.

    Saddle Bracket

    The Saddle Bracket attaches to the top rail with pins and wedges to provide a seat for forms when upper wall thickness is reduced.


  • Stiffback.

    Stiffback

    Providing the ability to stiffen vertically stacked forms and assisting in maintaining a plumb wall. Hole pattern specific.


  • Telescoping Beam Telescoping Beam.

    Telescoping Beam

    Telescoping Beams are used on decking systems in conjunction with shoring posts to provide support for the deck.


  • Tie Puller Ram Style.

    Tie Puller - Ram Style

    Tie pullers are designed to work with all pull ties. They help remove the tie with little effort while protecting the wall. Several styles are available to choose from. For additional information on which style would work best for your situation please contact your sales manager.


  • Tie Puller S Style.

    Tie Puller - S Style

    Tie pullers are designed to work with all pull ties. They help remove the tie with little effort while protecting the wall. Several styles are available to choose from. For additional information on which style would work best for your situation please contact your sales manager.


  • Turnbuckle Steel full view.

    Turnbuckle - Steel

    Straighten a wall and secure it in place prior to pouring with the Steel Turnbuckle. It connects to a 2x4 or stake in the ground and the other end pins to the form.

  • Turnbuckle Steel attached to the aluminum form. Turnbuckle Steel with round footing stake.


  • Turnbuckle for Wood Support

    Turnbuckle for Wood Support

    Straighten a wall and secure it in place prior to pouring with the Steel Turnbuckle. Connect one to each end of a 2x4. It then connects to a metal or 2x4 stake in the ground and the other end pins to the form. Twist the threaded ends to adjust.


  • Wall Aligner

    Wall Aligner

    The Wall Aligner moves small sections of the wall in or out. Available with or without spoon.


  • Wall Puller

    Wall Puller

    The Wall Puller is designed to pull long lengths of wall. The chain is adjustable for different footing widths. Available with or without spoon.


  • Wire Tie

    Wire Tie

    Allows for rapid positioning and securing of Re-Bar. Looped on both ends to receive the Wire Tie Twister for speedy tying. Available in the following sizes 5”, 6", and 8".


  • Wire Tie Twister

    Wire Tie Twister

    The Tie Twister allows quick tying of Precise Wire Ties.